35g/h 120W Salt Chlorine Generator Electrolytic Pool Chlorinator 220V

1 [Control Button] Easy to install, clean and maintain, which is simple to operate and fully functional for efficient chlorine production, and the system can be powered on or off manually using a button. Left and right arrows select working time and time end, and three time amounts can be set. 2 [Salinity Level] Displays the average measurement of recent salinity levels in pool water. Real time salinity readings are constantly updated with average values. When first installed, this reading may show the last salinity reading from the factory. This average will begin to update as the pool operates during the previous 24 hours. 3 [Winter Mode] Temporarily increase the chlorine output to maximum power for 24 hours, or until the system loses power, and reduce the selected chlorine output setting by half during cold weather periods when chlorine demand is low. 4 [Chlorine Output] Use the left and right arrows buttons to increase or decrease the system's power setting (chlorine gas production rate) to customize operation to your pool's needs. In the menu, the left and right arrows change options for pool temperature, instant salinity, and the mobile version. 5 [Simple To Use] A salt chlorinator is another method of cleaning swimming pools with chlorine through an electrolysis process. The electrolysis process is accomplished by passing salt water through an electrolyzer, where the sodium chloride in the water is converted into chlorine to achieve pool water cleaning.Item Type: Salt Chlorine Generator
Material: PVC
Controller Length: Approx. 35.5cm / 14in
Controller Width: Approx. 23cm / 9.1in
Controller Height: Approx. 15cm / 5.9in
Salt Chlorine Generator Length: Approx. 34.5cm / 13.6in
Type: Cleaning
Power Consumption: 120W
Model: RCL-35
Application: Swimming pool cleaning
Chlorine Production (g/h): 35
Waterproof Grade: IP44
Working Power: 220V/50HZ
Input Connector Diameter: Approx. 50mm / 2in
Output Connector Diameter: Approx. 63mm / 2.5in
Applicable Swimming Pool (m ): 175
System mainly consists of three parts: Control unit, electrolyzer and flowing switch
Weight: Approx. 8650g / 305.1oz
1. Parameter
Swimming Pool
Spas
Free Chlorine
1.0 to 3.0 ppm
3.0 to 5.0 ppm
Salinity
3000 to 4000 ppm
3000 to 4000 ppm
PH
7.2 to 7.8
7.2 to 7.8
Cyanuric Acid (stabilizer)
60 to 80 ppm
60 to 80 ppm
Total Alkalinity
80 to 120 ppm
80 to 120 ppm
Calcium Hardness
200 to 400 ppm
150 to 450 ppm
Saturation Index
-0.2 to 0.2
-0.2 to 0.2
2. Introduction:
The chlorine generator, by electrolysis, creates chlorine to sanitize your pool from the salt molecules (NaCL) in your water. A small electric charge is applied across a set of titanium plates inside the Electrolytic Cell. This produces Sodium Hypochlorite (NaOCl). In water, Sodium Hypochlorite dissociates into sodium (NA+) and hypochlorite (OCl-) ions. It is the hypochlorite ions that form with the hydrogen (H+) ions (from the water) to form hypochlorous acid (HOCl), which is the active agent that destroys bacteria and algae,and oxidizes organic matter. This form of chlorine works quickly in the pipe, leaving only a mild residual in the pool. In addition, the Electrolytic Cell continuously"shocks"the incoming water burning off any oils, organic matter, or other particles that need to be oxidized.Best of all, the process continuously recycles the salt: after cleaning the pool, the original molecules reform and the whole process begins again. The salt doesn't get used up!
3. Electrolytic Cell:
Creates chlorine as the water inside passes through and returns to the pool. The Electrolytic Cell ("Cell") contains a number of titanium plates that use a low level of electrical power to generate chlorine from salt in the water. The Cell comes with Unions to connect to the plumbing; each Union has a Threaded Collar that secures the Cell to the Unions, and enables the Cell to be easily removed for cleaning and inspection purposes.
4. Menu:
Press sequentially to cycle through the following information:
1.Pool Temperature (xx degrees Fahrenheit or Celsius)
2.Cell Voltage (in many cases 21.0 to 27.0 volts when chlorine is being generated, otherwise 16-31V)
3.Cell Current (in many cases 2.50 to 7.80 amps when chlorine is being generated, otherwise 0 amps during normal rest cycles.)
4.Real-Time Salinity reading ( xxxx ppm or x.x grams/Liter.)
5.System ID
6.Software revision level
7.Cell Version.
8.Timer
5. Water Chemistry:
As with any pool, it is important that you maintain proper water chemistry of the pool water,including pH, alkaline content, and calcium levels. The only special requirement is to maintain proper levels of salt and stabilizer. It is important to maintain these levels in order to prevent corrosion or scaling and to ensure maximum enjoyment of the pool. Test your water periodically. It is recommended that pool water be professionally tested a minimum of twice per season. Your local pool store can provide you with the chemicals and procedures to adjust the water chemistry. Be sure to tell the pool store that you are using a salt chlorine generator.
6. LED Indicator Lights:
Power: Located on the Power Button, this LED indicates that the Control Unit is receiving input power when illuminated.
Generate: This LED is illuminated during normal operation, and indicates that the system is able to generate chlorine. When flashing, the pool water is either too hot or too cold for chlorine generation.This light may be off during rest periods of the system's duty cycle
Super CL: Located on the Super CL Button, this LED is illuminated when the Super CL mode is active.
Remote: This part is controlled by a remote control system.
Winter Mode: Located on the Winter Mode Button(snow flake icon),this LED is illuminated when the winter mode has been activated.
Salinity: Located on the Salinity button, this LED is illuminated when the button has been pressed to display the salt level reading.
No Flowing: This LED is illuminated when the Flowing Switch has detected no flowing. This causes the Cell to stop generating chlorine. A flashing LED indicates that the flowing is restored, but there will be a 60 second delay before generation is reestablished.
Lo Salt: When this LED is flashing, the salt level is near to its minimum threshold,which is causing the Cell to operate at low efficiency. When this LED is illuminated steadily, the salt level is too low and Cell has shut down. The salt level must be raised before operation is restored. See "Adding Salt" for more information.
Hi Salt: When this LED is flashing, the salt level is higher than necessary. When this LED is illuminated steadily, the salt level is too high and the Cell has shut down. The pool water must be diluted with freshness water before operation is restored.
Timer: This LED is illuminated during works in your setting time.
Check Cell: When this LED is illuminated, Cell efficiency is greatly reduced, or it is time for regularly scheduled Cell inspection. When illuminated, the Cell has stopped producing chlorine. The Electrolytic Cell should be inspected and cleaned (if necessary). Remove power from the system, and inspect the Cell. If mineral build up is present, clean Cell according to the instructions on page 22. If after inspection, the Check Cell light is still on after restoring power to the system, then 20cleaning is necessary even if mineral build up wasn't immediately visible to the eye. If illuminated after cleaning, Cell replacement may be necessary. This light takes priority over any salinity indicators.
SAFETY notice: Using the Power Button to turn the system OFF does not remove power from the control box. Always disconnect power at the circuit breaker prior to attempting any service procedure.
7. Flowing Switch:
This component detect the water flowing in pipe and protect the system.

What's in the box
1 x Salt Chlorine Generator Controller, 4 x Adapter Connector, 1 Package x Accessories Bag (4 x Screws, 4 x Expansion Tubes, 2 x Washers, 3 x Other Accessories), 1 x Connector With Wire, 1 x Salt Chlorine Generator, 1 x English Manual