Ancel Ds600 Bt Full System Diagnostic Tool

Please Note: Electronics And Software Are Not Refundable (Please Read The Ad Carefully Before Purchasing)

DS600BT: Professional Car Diagnostic Scanners for Passenger Vehicles

Lifetime Free Software Update, 0-Risk Purchase & Reliable Seller

Powerful Bi-Directional Control

As a bi-directional scan tool, DS600 BT allows you to request information from a vehicle's ECU or send

commands to the vehicle's modules to perform specific tests and functions, such as EVAP Tests, Turn on/off

radiator fan, Window/Mirror/Door Lock Test, Pump and Value Tests, Sound horn Test, et. Without using the

vehicle control system and dismantling car's parts, it can quickly and accurately pinpoint the fault causes,

simple operation saves time and money.

34+ Hot Special Functions

ANCEL DS600 BT Bluetooth obd2 scanner covers almost all common services including Oil Reset, EPB, SAS, BMS

Reset, ABS bleed, Throttle Reset, Suspension, Injector Coding, Power Balance, Transmission Adaptation, Fuel

Trim Learn, HVAC Control Module Calibrate, Language Change, A/F Settings, Stop/Start Reset, Crankshaft

Sensor Relearn, TPMS, PMI function and etc. Imagine how much money and time you spend on car

maintenance every year? K8 pro car scanner will be a good helper and saver for your car. NOTE: Please check

compatibility before order.

Newly Added CAN FD & DOIP Protocol

Supporting CANFD and DOIP protocol, K8 pro obd2 scanner will save you 200+ bucks as no need extra buy for

special adapter. CANFD protocol suits for the latest GM (2019-), reducing the risk of undetected errors. The

DoIP protocol (comes with DoIp cable) fits for 2017+ BMW (F&G chassis), for Jaguar & Land Rover after 2017,

for Volvo after 2018. Plus, supporting FCA Autoauth allows you to unlock the SGW module on 2017+ FCA

Vehicles (for Chrysler/ Dodge/Jeep/Alfa Romeo/Fiat, etc.).

ANCEL DS600BT Support 34+ Special Functions

1.Oil Reset

The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset the cluster or

driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new

maintenance cycle.

2.D-P-F Regeneration

D-P-F Regeneration is used to clear PM(Particulate Matter)from the D-P-F filter through continuous combustion

oxidation mode(such us high temperature heating combustion, fuel additive or catalyst reduce PM ignition

combustion)to stabilize the filter performance.

D-P-F regeneration may be performed in the following cases:

a)The exhaust back pressure sensor is replaced.

b)The PM trap is removed or replaced

c)The fuel additive nozzle is removed or replaced

d)The catalytic oxidizer is removed or replaced.

e)The D-P-F regeneration MIL is on and maintenance is performed.

f)The D-P-F regeneration control module is replaced.

3.AFS(headlamp) Reset

The feature is used to initialize the adaptive headlamp system. According to the ambient light intensity, the

adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjust the

headlamp lighting angle while monitoring the vehicle speed and body posture.

4.E-G-R Adaption

This function is used to learn the E-G-R(Exhaust Gas Recirculation)valve after it is cleaned or replaced.

5.Brake-pad Reset

If the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on

board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad.

Otherwise, the car alarms.

Reset must be performed in the following cases:

a)The brake pad and brake pad wear sensor are replaced.

b)The brake pad indicator lamp is on.

c)The brake pad sensor circuit is short, which is recovered.

d)The servo motor is replaced.

6.IMMO Service

To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed

so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use

the car. When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote

control battery is replaced, anti-theft key matching must be performed.

7.Windows Calibration

This feature is designed to perform door window matching to recover ECU initial memory, and recover the

automatic ascending and descending function of power window.

8.Coolant Bleeding

Use this function to activate the electronic water pump before venting the cooling system.

9.Steering Angle Reset

To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking

this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing

the steering angle position sensor ,replacing steering mechanical parts(such as steering gearbox, steering

column, end tie rod, steering knuckle),performing four-wheel alignment, or recovering car body, you must

reset the steering angle.

10.Injector Coding

Writing injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as

to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector

code of each cylinder must be confirmed or re-coded so that cylinder can better identify injectors to accurately

control fuel injection.

11.Seat Calibration

This function is applied to match the seats with memory function that are replaced and repaired.

12.Transport Mode

In order to reduce power consumption, the following functions may be disabled, including limiting the vehicle

speed, not waking up the door opening network, and disabling the remote control key, etc. At this time, the

transport mode needs to be deactivated to restore the vehicle to normal.

13.Battery Matching

This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which

the original low battery fault information will be cleared and battery matching will be done.

Battery matching must be performed in the following cases:

a)Main battery is replaced. Battery matching must be performed to clear original low battery information and

prevent the related control module from detecting false information. If the related control module detects

false information, it will invalidate some electric auxiliary functions, such as automatic start & stop function,

sunroof without one-key trigger function, power window without automatic function.

b)Battery monitoring sensor. Battery matching is performed to re-match the control module and motoring

sensor to detect battery power usage more accurately, which can avoid an error message displaying on the

instrument panel.

14.Airbag Reset

This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collides and

the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicator lights up,

and the fault code can't be cleared. Since the data inside the airbag computer is disposable, it is required that

all new accessories must be replaced, but after performing this function, the data of the airbag computer can

be recovered and the fault code can be cleared, the airbag light will go out, and the airbag computer can

continue to use.

15.Tyre Reset

This function is used to set the size parameters of the modified or replaced tire.

16.Cluster Reset

a)cluster reset is to copy, write, or rewrite the value of kilometers in the chip of cluster by using a car

diagnostic computer and data cable, so that the cluster shows the actual cluster.

b)Usually when the cluster is not correct due to the damaged vehicle speed sensor or cluster failure, it is

necessary to do cluster reset after maintenance.

17.ABS Bleeding

When the ABS contain air, the ABS bleeding function must be performed to bleed the brake system to restore

ABS brake sensitivity. If the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake

fluid is replaced, the ABS bleeding function must be performed.

18.Gear Learning

The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computer to more

accurately diagnose engine misfires. lf gear learning is not performed for a car equipped with Delphi engine,

the MlL turns on after the engine is started. The diagnostic device detects the DTC P1336'gear not learned'. In

this case, you must use the diagnostic device to perform gear learning for the car. After gear learning is

successful, the MIL turns off. After the engine ECU, crankshaft position sensor, or crankshaft flywheel is

replaced, or the DTC 'gear not learned" is present, gear learning must be performed.

19.Language Change

This function is used to change the system language of the vehicle central control panel.

20.Adblue Reset

After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.

21.Elec. Throttle Adaption

Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value

of the ECU returns to the initial state. By doing these, the movement of the throttle (or idle motor)can be more

accurately controlled, thus adjust the intake volume.

22.Suspension Matching

This function can adjust the height of the body. When replacing the body height sensor in the air suspension

system, or control module or when the vehicle level is incorrect, you need to perform this function to adjust

the body height sensor for level calibration.

23.A/F Reset

This function is applied to set or learn Air/Fuel ratio parameters.

24.Nox Sensor Reset

Nox sensor is a sensor used to detect the content of nitrogen oxides (NOx)in engine exhaust. If the NOx fault is

re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned

value stored in the engine ECU.

25.TPMS Reset

After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting function must

be performed to reset tire pressure and turn off the tire pressure MIL. Tire pressure resetting must be

performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tire

pressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, and tire is

replaced for the car with tire pressure monitoring function.

26.A/T Learning

This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox is

disassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impact

problem. In this case, this function needs to be done so that the gearbox can automatically compensate

according to the driving conditions so as to achieve more comfortable and better shift quality.

27.Sunroof Initialization

This function can set the sunroof lock off, closed when it rains, sliding/tilting sunroof memory function,

temperature threshold outside the car etc.

28.Stop/Start Reset

This function is used to open or close the automatic start-stop function via setting the hidden function in

ECU(provided that the vehicle has a hidden function and supported by hardware)

29. Motor angular position sensor calibration

When the motor works in a high temperature environment or in a humid, dusty and other environment for a

long time, the angular position sensor is prone to failure, and the signal of the angular position sensor is wrong

after the failure, resulting in the motor not working normally, the system reliability is reduced, and the normal

driving of the vehicle is affected. . At this time, it is necessary to calibrate the angular position sensor of the

motor.

30. Engine power balance

High-quality engine balance that helps the engine spin more freely at high revs, improves redline, and

increases power

31. High-voltage battery health inspection

32. Smart Cruise Control Calibration

Intelligent cruise control has the function of improving driving safety and comfort. When the intelligent cruise

module is replaced, use this function to learn and match, and the system can function normally.

33. Automatic air conditioning initialization

34. G-P-F regeneration (particle trap regeneration)

The function of g-p-f is to reduce particulate matter, and it is arranged on the exhaust system of the car to

collect the particulate matter in the organic exhaust gas of the car, reasonably Reduce the release of

particulate matter, and according to the ECU operation, carry out air oxidation and ignition of the particles in

the trap, and then do to regeneration

Please note: Functions may vary from vehicle make and model

Wireless OE-Level All Systems Diagnostics

Equipped with Bluetooth VCI, you can do car diagnostics out of the car (up to 33F/10M) without being

confined to a small space inside the car. Provides the convenience of Auto VIN, K8 pro allowing for easy access

and diagnosis of all available modules on a wide range of vehicles, like PCM, ECM, BCM, TPMS, SAS, Fuel

System, etc, to perform read/clear codes, view live data, freeze frame, perform active tests, and read ECU

info... 12-In-1 Data Stream Graphics make data viewing more intuitive. Diagnostic reports can be shared via QR

Code, Bluetooth or email. Built-in Browser and Fault Code Library allows you directly query the fault code

when diagnosing.

Active Test & Bi-Directional Control: Pinpoint Faults Easily

The DS600BT offers bi-directional control and active testing, allowing you to send commands to the vehicle'S

ECU and monitor component responses-critical for identifying faulty parts.

Examples of active tests include:

Activating the coolant pump to check circulation.

Opening/closing windows to test power window systems.

Controlling headlights, taillights, and turn signals to verify lighting functionality.

Adjusting rearview mirrors to test motor operation.

Triggering the horn to check audio system integrity.

Testing fuel injectors and wiper systems for proper operation.

Note: Active tests depend on the vehicle's electronic control units (ECUs). Only available tests for your specific

vehicle will appear in the menu.

Functions may vary from vehicle make and model

Support Protocols:

SAE J1850 PWM, SAE J1850 VPW, ISO 9141-2 ISO, ISO 14230-4 KWP, ISO 15765-4 CAN, CANFD,DOIP

ANCEL DS600 Supported 100000+ vehicle models:

Europe vehicle, after 2001 and newer:

Compatible with Vaz, Porsche, Maserati, BMW, Seat, VW, Audi, Citroen, Landrover, Smart, Renault, Skoda,

Sprinter, Land Rover, Benz, Fiat, Opel, Volvo, Peugeot, Ferrari, Saab, Gaz, DR

USA vehicles, after 1996 and newer:

Compatible with Gm, USAFord, Chrysler, Dodge ; Willy; Australia: Compatible with Austford, Holden; Brazil:

Compatible with BXFiat, BXGM

Aisa vehicles , after 2003 and newer :

Compatible with Changcheng, Daewoo, Huachen, Zhongxing, Indian Tata, JAC, Maruti, Perodua, Chery, Isuzu,

Jinlong, Suzuki, Saipa, HM, Hmazda, Ikco, Malaysia Proton, Luxgen, Toyota, Changan, Futian, Honda, Wuling, V

class, Jpisuzu, Kia, Indian Maruti, Indian Mahindra, Malaysia Perodua, Hafei, Lifan, Mahindra, Nissan, Xiali,

Zhongshun, Tata, Changhe, China GM, Saicmg, Mazda, Zhongtai, Daihatsu, BYD Flyer, Hyundai, Proton, Subaru,

Ssangyong, Joylong, Mitsubishi,Gonow, Qoros, Maxus, Mvm

Multi-Language Support:

28 languages, including English, German, Spanish, French, Italian, Portuguese, Japanese, Russian, Polish,

Turkish, Dutch, Hungarian, Traditional Chinese, Korean, Greek, Slovak, Romanian, Arabic, Croatian, Slovenian,

Finnish, Czech, Swedish, Danish, Persian, Serbian, Vietnamese, and Bulgarian.

Technical Specifications:

Operating System: Android 10

Display: 8.0-inch touchscreen color display

Storage: 4GB RAM + 64GB ROM

Battery: 4150mAh/3.8V (standby >10 days)

Connectivity: Bluetooth VCI, Wi-Fi (2.4/5.0GHz 802.11 ac/a/b/g/n)

Languages: 28 (including English, German, French, Spanish, etc.)

Certifications: CE, FCC, IC

Key Features: Designed for Convenience

1.8.0-inch Touchscreen Color Display: Responsive and easy to navigate, even in bright environments.

2.Bluetooth VCI Connection: Wireless pairing eliminates cable clutter, offering flexibility during diagnostics.

Android 10 OS: Smooth performance with 4+64GB storage, providing ample space for data logs and software

updates.

3.Long-Lasting Battery: 4150mAh/3.8V battery with over 10 days of standby time. Includes a 3-in-1 charging

adapter (EU, US, UK plugs) for global use.

4.Multi-Language Support: 28 languages, including English, German, Spanish, French, Italian, Portuguese,

Japanese, Russian, Polish, Turkish, Dutch, Hungarian, Traditional Chinese, Korean, Greek, Slovak, Romanian,

Arabic, Croatian, Slovenian, Finnish, Czech, Swedish, Danish, Persian, Serbian, Vietnamese, and Bulgarian.

5.Certifications: CE, FCC, IC compliant, ensuring quality and safety for the (European and American) markets.

What's in the box
1 x ANCEL DS600BT Diagnostic Scanner
1 x Bluetooth VCI Adapter
1 x Type-C Data Cable
1 x 3-in-1 Charging Adapter (EU/US/UK Plugs)
1 x 10-Language Paper Quick Start Guide