Mix Box Rivet Drill Adapter With Handle

Vertical handle grip, labor-saving, durable chrome-molybdenum steel (CrMO) gun head.Transforms your cordless screwdriver / drill into the strongest rivet gun for pop rivets.

Equipped with a detachable handle for more stable and controlled operation assistance.

Riveter Adapter is suitable for all types of blind rivets with a shank diameter of: 2.4 / 3.2 / 4.0 / 4.8 mm.

Electric Rivet Gun Adapter Quick Start Guide

Thank you for purchasing this product! To ensure smooth operation and avoid jams or damage, please take 2 minutes to read this guide before use. Correct operation can extend the adapter's lifespan to over 10,000 cycles.

Important! Must-Read Before Use (Core Tips to Prevent Jams)

99% of "broken after first use" cases are actually due to unremoved broken mandrels stuck inside the nosepiece, not product failure.Please follow the steps below carefully.

Detailed Operating Steps:

Step 1: Select the Correct Nosepiece

- Choose the nosepiece that matches the diameter of your rivet mandrel(typically 3.2mm, 4.0mm, etc.).

- Critical: Do not use a large nosepiece for a small rivet! Otherwise, the broken mandrel cannot eject smoothly and will likely get stuck.

Step 2: Install the Nosepiece

- Screw the selected nosepiece onto the front of the adapter. Tighten by hand only (no need to over-tighten).

- Ensure it is installed securely without wobbling.

Step 3: Insert the Rivet

- Insert the rivet completely into the nosepiece until the rivet head touches the end face of the nosepiece.

- Insert the rivet mandrel into the hole of the workpiece to be joined. Hold the nosepiece vertically and firmly against the workpiece surface.

Step 4: Riveting

- Press and hold the switch of the electric rivet gun until the rivet mandrel breaks with a "click" sound.

- Release the switch immediately to prevent the motor from running idle and damaging the internal collet.

Step 5: Clear the Broken Mandrel (After Each Riveting Cycle)

- After the mandrel breaks, it usually remains inside the nosepiece. Clean it promptly after each operation to prevent accumulation and jamming.

- Cleaning Method:

1. Turn off the electric rivet gun.

2. Unscrew the front sleeve of the adapter (or directly unscrew the nosepiece).

3. Use the provided ejector pin/thin iron rod to push the broken mandrel out from the front (nosepiece opening) towards the back.

4. Reinstall the sleeve/nosepiece. It's ready for use again.

- Never poke from the back, as this may damage the internal jaws.

Frequently Asked Questions:

Q: Why does it work fine the first time, but then loses power or jams the second time?

A:This is a classic case of not clearing the broken mandrel. Accumulated mandrel pieces inside the nosepiece hinder the collet's normal operation. Simply clean it following Step 5 to restore function.

Q: What if the rivet gets stuck or won't pull out during riveting?

A:1. Immediately disconnect power.

2. Unscrew the front sleeve and use the ejector pin to push the broken mandrel out from the front.

3. Check if the nosepiece matches the rivet diameter; replace if mismatched.

4. If jamming persists, the rivets might be of poor quality (irregular shaft, too hard/soft). Try using quality rivets.

Q: Can the adapter handle all rivet sizes?

A:Do not exceed the product's specified maximum pulling capacity (typically 3.2mm-5.0mm for stainless steel/aluminum rivets). Pulling oversized rivets can damage the collet.

Prohibited Actions:

- Never run the tool idle: Do not press the switch without a rivet installed. This will severely wear the collet, preventing it from gripping the mandrel.

- Avoid forceful operation: If the adapter becomes loose on the electric gun, tighten it promptly to prevent internal shaft twisting or damage.

- Avoid using low-quality rivets: Poor quality rivets with inaccurate dimensions or improper hardness/ductility are a common cause of jamming.

Maintenance Tips

- Regularly clean metal debris from inside the nosepiece.

- If not used for extended periods, apply a drop of light lubricating oil to the collet area to prevent rust.

- When changing nosepieces, tighten by hand only; do not use tools to force them.

Note: This guide applies to most electric rivet gun adapters. Specific structures may vary slightly. Refer to the actual product.

Color: Black

Material: Chrome Molybdenum Steel

Package Dimensions: 7.5cm x 5.2cm x 6.2cm (19.05in x 13.20in x 15.74in)

Weight: 0.45kg (0.99lb)

Note:

Periodically clean metal debris from inside the gun head.

If the tool is to remain unused for an extended period, apply a small amount of lubricating oil to the chuck to prevent rust.

When replacing the nozzle, do not use tools to forcibly tighten it; hand-tightening is sufficient.

Due to lighting and screen settings, please allow for slight color differences.

Due to manual measurement, please allow for slight dimensional differences.

What's in the box
1 x Rivet Gun Conversion Adapter With Handle
1 x Wrench
1 x 2.4mm Diameter Rivet Head
1 x 3.2mm Diameter Rivet Head
1 x 4.0mm Diameter Rivet Head
1 x 4.8mm Diameter Rivet Head