OrcaTorch SD01 Pro Dive Beacon - 150 m Waterproof AAA Tank Marker Light
Ultra-compact 25 g strobe / constant signal light with 37-70 hour runtime for scuba tanks, SMBs & night dives
Takealot · checked Today
2 offers · 1 retailers
Listed under the same model number
No barcode ties these listings together, so no saving is claimed. See the listings
Matched by model number; no shared barcode
- Average
- R 479.00
- Lowest seen
- R 479.00
- Highest seen
- R 479.00
- Last change
- R 0.00
- First indexed
- 21 Sep 2026
- Retailer
- Takealot
Description
Small body, big signal. The OrcaTorch SD01 Pro is a rugged micro beacon built to keep you seen underwater - on your tank valve, DSMB, scooter, on your hand or guideline. One AAA battery powers either a steady glow or a 1.5 Hz flash, delivering up to 70 hours of burn time so your team / diving partner can track you from descent to deco.
Key Features:
- Two modes: Constant-on or 1.5 Hz flash for instant visibility choices underwater.
- Serious depth rating: Sealed to 150 m / 500 ft for wrecks, caves and deep tech dives.
- Featherweight & compact: Just 77.5 mm long, 19 mm in diameter and 25 g - clips anywhere, on your gear and never in the way.
- Field-friendly power: Runs on a single, widely available AAA cell (included).
- Ready to dive: Comes with spare O-rings and a lanyard for quick attachment and maintenance.
Specifications:
- Power Source: 1 × AAA battery
- Modes & Runtime: Constant ( 37 h) / Flash ( 70 h)
- Dimensions: 77.5 mm (L) × 19 mm (Ø)
- Weight: 25 g (without battery)
- Depth Rating: 150 m / 500 ft
- Included Accessories: AAA battery, lanyard, spare O-rings
- Color Choices: Blue, Red, Green, White, Orange (one color per light)
Clip it, click it, and light up your position. The SD01 Pro is the no-fuss, always-visible marker every diver should carry - because being seen is being safe.
Quick-Start / Manual Instructions:1. Install the Battery- Unscrew the beacon at the orange ring (body separates from dome).
- Insert 1 × AAA battery positive end first toward the LED head.
- Inspect and lightly grease both O-rings; make sure they sit flat and free of sand/hair.
- Reassemble and tighten until fully seated.
2. Power & Modes
- ON (Constant): Tighten the cap fully.
- Switch to Flash (1.5 Hz): Loosen a quarter turn, then retighten within 2 seconds.
- OFF: Loosen the cap until the light goes out.
(Tip: Practice topside so you know the feel with gloves on.)
3. Mounting / Use Underwater
- Clip or tie the lanyard to your tank valve, DSMB, scooter, camera rig, or guideline.
- Do a shallow-water leak check before any deep, wreck or cave dive.
4. Post-Dive Care
- Rinse thoroughly in fresh water with the light assembled.
- Dry, then open, remove the battery if storing >1 week.
- Wipe and re-grease O-rings periodically.
5. Maintenance
- Replace O-rings if cracked, flattened, or sticky.
- Only use silicone-based dive grease.
- Avoid mixing old and new batteries.
6. Troubleshooting
- No light: Check battery orientation/charge, clean contacts, verify O-rings not pinched.
- Flicker: Tighten fully; inspect O-rings and threads for debris.
- Leaks/condensation: Stop use, dry immediately, replace O-rings and test shallow.
7. Safety Notes
- Do not stare directly into LED at close range.
- Keep out of reach of small children; contains small parts and batteries.
- Dispose of batteries according to local regulations.
What's in the box
1 x SD01 Pro dive beacon light
1 x AAA alkaline battery
2 x Spare O-rings
1 x Wrist/gear lanyard
1 x Zip carry case
1 x User Manuel