Solar LED House Number Sign with 12 Light Modes, IP44, Dual Mount

1. 12 Selectable Light Modes

Choose from warm white, cool white, red, green, blue, mixed white, purple, orange, cyan and dynamic lighting effects using the built-in button control.

2. Solar Powered Address Visibility

The 1W monocrystalline solar panel charges the built-in battery during daylight, helping illuminate house numbers at night without mains wiring.

3. 30lm LED Address Lighting

Ten 5050 LED chips provide up to 30lm of illumination, designed to make house numbers easier to identify after dark rather than illuminate a large outdoor area.

4. Dual Installation Design

Use the dual ground stakes for lawns and garden beds or install the address sign using the supplied wall-mount hardware where suitable.

5. 1800mAh Battery with Extended Runtime

The built-in 3.7V 1800mAh lithium battery provides a stated runtime of over 30 hours after a full charge under suitable charging and usage conditions.

Specifications

Product Type: Solar LED Address Sign

Product Category: Solar House Number Light

Colour: Black

Material: PET + ABS

Light Source: 10 x 5050 SMD LEDs

Brightness: Up to 30lm

Light Modes: 12 Selectable Modes

Light Colours: Warm White, Cool White, Red, Green, Blue, Mixed White, Purple, Orange and Cyan

Dynamic Modes: Colour Change, Breathing and Flashing

Dimmable: No

Motion Sensor: No

Switch Type: Button / Manual Control

Solar Panel Type: Monocrystalline Silicon

Solar Panel Rating: 5V / 200mA / 1W

Solar Panel Size: Approx. 180 x 42mm

Battery Type: Built-in 18650 Lithium Battery

Battery Capacity: 1800mAh

Battery Voltage: 3.7V

Charging Time: Approx. 5 Hours under Suitable Sunlightx

Stated Runtime: Approx. 30+ Hours after a Full Chargex

Protection Rating: IP44

Installation Type: Ground Stake or Wall Mount

Product Body Size: Approx. 27.7 x 4.3 x 15cm

Net Weight: Approx. 433g

Main Use: Outdoor House Number and Address Visibility

Suitable Areas: Gates, Driveways, Garden Entrances, Boundary Walls and Home Entrances

xCharging and runtime depend on sunlight, weather, battery condition, selected lighting mode and usage conditions.

1. Install in Suitable Sunlight

Position the solar panel where it can receive sufficient direct sunlight during the day. Shaded installation may reduce charging performance and lighting time.

2. Set the Product to ON Before Use

Make sure the power switch is set to ON before charging and normal operation. Use the button control to select the preferred lighting mode.

3. Runtime May Vary

The stated 30+ hour runtime is based on suitable charging conditions. Actual lighting time may vary according to sunlight, weather, battery condition, selected lighting mode and usage.

4. IP44 Outdoor Protection

The product is suitable for normal outdoor splash and light-rain exposure. Do not submerge it, install it in standing water or expose it to prolonged water immersion.

5. Designed for Address Visibility

The 30lm LED output is intended to illuminate house numbers and address information. It is not designed as a security light, floodlight or general area light.

6. Install Ground Stakes in Suitable Soil

Use the ground stakes in soil, lawn or garden-bed areas. Do not force the stakes directly into concrete, stone or other hard surfaces.

7. Handle the Solar Panel and Housing Carefully

Keep the solar panel surface clean and avoid heavy impact, scratching, bending or placing excessive weight on the address sign.

8. Battery and Heat Care

Keep the product away from excessive heat and open flames. Battery performance and service life may gradually reduce with age, repeated charging and environmental conditions.

What's in the box
1 x Solar LED Address Sign 4 x Extension Rods 2 x Ground Stakes 2 x Connectors/End Caps 1 x Wall-Mount Bracket 2 x Screws 2 x Wall Plugs 2 x Mounting Fittings 4 x Number Sticker Sets (0-9) 2 x Letter Sticker Sets (A-Z) 3 x AlignmentFrames 1 x DIY CreativeSticker