Teltonika RUT956

Teltonika RUT956

Industrial LTE cellular router

R 6 639.00

Takealot · checked 8 days ago

View at Takealot

3 offers · 2 retailers

Listed under the same model number

No barcode ties these listings together, so no saving is claimed. See the listings

Matched by model number; no shared barcode

Average
R 7 115.00
Lowest seen
R 6 639.00
Highest seen
R 7 115.00
Last change
-R 476.00
First indexed
13 Nov 2026
Retailer
Takealot

Each price is from PriceFind's last check of that retailer. Follow the link for the live price.

Description

RUT956 is an industrial router that combines cellular, Wi-Fi, and wired connectivity options with automatic WAN failover and GNSS capabilities. Serial communication interfaces enable integrating more varied devices into the solution ecosystem, while I/O and advanced RutOS software facilitate equipment control, automation, and event notifications.

MOBILE
Mobile module: 4G (LTE) - Cat 4 up to 150 Mbps, 3G - Up to 42 Mbps, 2G - Up to 236.8 kbps

SIM switch: 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection

Status: Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID

SMS: SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP

USSD: Supports sending and reading Unstructured Supplementary Service Data messages

Black/White list: Operator black/white list

Multiple PDN: Possibility to use different PDNs for multiple network access and services

Band management: Band lock, Used band status display

APN: Auto APN

Bridge: Direct connection (bridge) between mobile ISP and device on LAN

Passthrough: Router assigns its mobile WAN IP address to another device on LAN

WIRELESS
Wireless mode: IEEE 802.11b/g/n, Access Point (AP), Station (STA)

WiFi security: WPA2-Enterprise - PEAP, WPA2-PSK, WEP, WPA-EAP, WPA-PSK; AES-CCMP, TKIP, Auto Cipher modes, client separation

SSID/ESSID: SSID stealth mode and access control based on MAC address

WiFi users: Up to 100 simultaneous connections

Wireless Hotspot: Captive portal (Hotspot), internal/external Radius server, built in customizable landing page

ETHERNET
WAN: 1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX

LAN: 3 x LAN ports, 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX

NETWORK
Routing: Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, NHRP)

Network protocols: TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SMNP, MQTT, Wake On Lan (WOL)

VoIP passthrough support: H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Connection monitoring: Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection

Firewall: Port forward, traffic rules, custom rules

DHCP: Static and dynamic IP allocation, DHCP Relay, Relayd

QoS / Smart Queue Management (SQM): Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

DDNS: Supported >25 service providers, others can be configured manually

Network backup: WiFi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic Failover

Load balancing: Balance Internet traffic over multiple WAN connections

Hotspot: Captive portal (Hotspot), internal/external Radius server, SMS authorization, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customizable themes

SSHFS: Possibility to mount remote file system via SSH protocol

SECURITY
Authentication: Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, IP & Login attempts block

Firewall: Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T

Attack prevention: DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

VLAN: Port and tag based VLAN separation

Mobile quota control: Custom data limits for both SIM cards

WEB filter: Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only

Access control: Flexible access control of TCP, UDP, ICMP packets, MAC address filter

VPN
OpenVPN: Multiple clients and a server can run simultaneously, 27 encryption methods

OpenVPN Encryption: DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256

IPsec: IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)

GRE: GRE tunnel, GRE tunnel over IPsec support

PPTP, L2TP: Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support

Stunnel: Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program's code

DMVPN: Method of building scalable IPsec VPNs

SSTP: SSTP client instance support

ZeroTier: ZeroTier VPN client support

WireGuard: WireGuard VPN client and server support

Tinc: Tinc offers encryption, authentication and compression in it's tunnels. Client and server support.

MODBUS TCP SLAVE
ID range: Respond to one ID in range [1;255] or any

Allow Remote Access: Allow access through WAN

Custom registers: MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Slave functionality

MODBUS TCP MASTER
Supported functions: 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats: 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)

MODBUS RTU MASTER (RS232)
Supported baud rates: From 300 to 115200

Supported functions: 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats: 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

Number of data bits: From 5 to 8

Number of stop bits: 1 or 2

Parity: None, Even, Odd

Flow: None, RTS/CTS, Xon/Xoff

Duplex: Full duplex

MODBUS RTU MASTER (RS485)
Supported baud rates: From 300 to 300000

Supported functions: 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats: 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

Number of data bits: 8

Number of stop bits: 1

Parity: None, Even, Odd

Flow: None, Xon/Xoff

Duplex: Half duplex

MODBUS DATA TO SERVER
Protocol: HTTP(S), MQTT, Azure MQTT, Kinesis

MQTT GATEWAY
MQTT Gateway: Allows sending commands and receiving data from MODBUS Master through MQTT broker

DNP3
Supported modes: TCP Master, DNP3 Outstation, RTU Master

MONITORING & MANAGEMENT
WEB UI: HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log

FOTA: Firmware update from server, automatic notification

SSH: SSH (v1, v2)

SMS: SMS status, SMS configuration, send/read SMS via HTTP POST/GET

Call: Reboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer, WiFi on/off

TR-069: OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem

MQTT: MQTT Broker, MQTT publisher

SNMP: SNMP (v1, v2, v3), SNMP Trap

JSON-RPC: Management API over HTTP/HTTPS

MODBUS: MODBUS TCP status/control

RMS: Teltonika Remote Management System (RMS)

IOT PLATFORMS
Cloud of Things: Allows monitoring of: Device data, Mobile data, Network info, Availability

ThingWorx: Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type

Cumulocity: Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength

Azure IoT Hub: Can send device IP, Number of bytes send/received, Temperature, PIN count to Azure IoT Hub server, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type

SYSTEM CHARACTERISTICS
CPU: Mediatek MIPS 24Kc 580 MHz

RAM: 128 MB, DDR2

FLASH storage: 16 MB, SPI Flash

FIRMWARE / CONFIGURATION
WEB UI: Update FW from file, check FW on server, configuration profiles, configuration backup

FOTA: Update FW

RMS: Update FW/configuration for multiple devices at once

Keep settings: Update FW without losing current configuration

FIRMWARE CUSTOMIZATION
Operating system: RutOS (OpenWrt based Linux OS)

Supported languages: Busybox shell, Lua, C, C++

Development tools: SDK package with build environment provided

LOCATION TRACKING
GNSS: GPS, GLONASS, BeiDou, Galileo and QZSS

Coordinates: GNSS coordinates via WebUI, SMS, TAVL, RMS

NMEA: NMEA 0183

NTRIP: NTRIP protocol (Networked Transport of RTCM via Internet Protocol)

Server software: Supported server software TAVL, RMS

Geofencing: Configurable multiple geofence zones

SERIAL
RS232: DB9 connector, full RS232 (with RTS, CTS)

RS485: RS485 Full Duplex (4 wires) and Half Duplex (2 wires). 300-115200 baud rate

Serial functions: Console, Serial over IP, Modem, MODBUS gateway, NTRIP Client

USB
Data rate: USB 2.0

Applications: Samba share, USB-to-serial

External devices: Possibility to connect external HDD, flash drive, additional modem, printer

Storage formats: FAT, FAT32, NTFS

INPUT / OUTPUT
Input: 1 x digital dry input (0 - 3 V), 1 x digital galvanically isolated input (0 - 30 V), 1 x analog input (0 - 24 V), 1 x Digital non-isolated input (on 4-pin power connector, 0 - 5 V detected as logic low, 8 - 30 V detected as logic high)

Output: 1 x digital open collector output (30 V, 250 mA), 1 x SPST relay output (40 V, 4 A), 1 x Digital open collector output (30 V, 300 mA, on 4-pin power connector)

Events: Email, RMS, SMS

I/O juggler: Allows to set certain I/O conditions to initiate event

POWER
Connector: 4-pin industrial DC power socket

Input voltage range: 9 - 30 VDC, reverse polarity protection; surge protection >31 VDC 10us max

PoE (passive): Passive PoE over spare pairs. Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, LAN1 Port, 9 - 50 VDC

Power consumption: < 2 W idle, < 7 W Max

PHYSICAL INTERFACES
Ethernet: 4 x RJ45 ports, 10/100 Mbps

I/O's: 2 x Inputs and 2 x Outputs on 10-pin industrial socket, 1 x Digital input and 1 x Digital output on 4-pin power connector (available from HW revision 1600)

Status LEDs: 1 x bi-color connection status LED, 5 x connection strength LEDs, 4 x LAN status LEDs, 1 x Power LED

SIM: 2 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders, eSIM (Optional)

Power: 1 x 4-pin power connector

Input/output: 1x 10 pin industrial socket for inputs/outputs

Antennas: 2 x SMA for LTE, 2 x RP-SMA for WiFi, 1 x SMA for GNSS

USB: 1 x USB A port for external devices

RS232: 1 x DB9 socket

RS485: 1 x 6-pin industrial socket

Reset: Reboot/User default reset/Factory reset button

PHYSICAL SPECIFICATION
Casing material: Aluminium housing, plastic panels

Dimensions (W x H x D): 110 x 50 x 100 mm

Weight: 287 g

Mounting options: DIN rail (can be mounted on two sides), flat surface placement

OPERATING ENVIRONMENT
Operating temperature: -40 C to 75 C

Operating humidity: 10% to 90% non-condensing

Ingress Protection Rating: IP30

REGULATORY & TYPE APPROVALS
Regulatory: CE/RED, UKCA, CB

What's in the box
1 x ROUTER RUT956
1 x 9 W PSU
2 X LTE ANTENNAS (MAGNETIC MOUNT, SMA MALE, 3 M CABLE)
2 X WIFI ANTENNAS (MAGNETIC MOUNT, RP-SMA MALE, 1.5 M CABLE)
1 x GNSS ANTENNA (ADHESIVE , SMA MALE, 3 M CABLE)
1 x RS485 CONNECTOR BLOCK
1 x I/O CONNECTOR BLOCK
1 x ETHERNET CABLE (1.5 M)
1 x SIM ADAPTER KIT

Similar products